|
STOP
- Before you go any further, if sterility is a
concern, do not ball pump. There is not enough
evidence that ball pumping does or does not cause
temporary or permanent sterility. It makes sense
that if you introduce lymph into the scrotum,
the testicles will not be able to snug up close
or hang away from the body to obtain the ideal
temp for sperm production. It also makes sense
that negative pressures may cause a disturbance
in the testicle. So If if in doubt, bail out!
Previous
| Next Article: Ball
Pumping - pumping guide
Ball
Pumping - Equipment
So
you ready to get started in ball pumping eh?
First
thing you should know is that you CAN pump your
balls in one cylinder, but it becomes a hassle
when trying to keep that pesky penis from getting
sucked in. Therefore, it is common practice to
pump both cock and balls at the same time
out of convenience.
So
what you will need besides a handpump is a cylinder
to house both penis and scrotum. There are the
three categories of penis and scrotum cylinders:
Single
stage cylinder
Multi stage cylinder
Specialty system
A
single stage cylinder
is a cylinder that is made up of one part, or
one cylinder. An example of this is the Dr Joel
Kaplan cylinders. For penis pumping, these cylinder
range from 1.75"
to 2.5" diameter, but for penis and scrotum
pumping, you must utilize a larger cylinder that
run from 2.75"
to 3.5" diameter.
These
cylinders are the most inexpensive to purchase
and are considered entry level for beginner ball
pumpers. Folks with large packages should consider
a multi level cylinder or a specialty system to
avoid genital distortion, caused when pumping
huge packages in tight quarters.
Here
is Dr Joel Kaplan's sizing
matrix to
determine the best size penis and scrotum cylinder
based on your current erect dimensions.
Another
option is PumpToy's
LongJohnny which only comes in one size, 4"
diameter, but has a seal at the base that restricts
the opening to 2.75-inch diameter. A great buy
if you plan grow but only want to spend your hard
earned cash on a one size fits all cylinder.
A
multi stage cylinder
is a cylinder that is made up of more than one
part, or more than one cylinder. Usually the multi-level
cylinder has a smaller diameter base that contacts
the groin, which then expands into a larger diameter
cylinder. It is common for the larger cylinder
to be 5-inches in diameter. An example of a multi
stage cylinder is PumpToy's
STJ cylinder - this cylinder has a seal that
restricts the base to a 2.75" diameter opening
but flares out to a whopping 5-inches for maximum
growth.
These
multi stage cylinders are designed to ALLOW the
penis and scrotum enough area to grow without
smashing into the sidewalls. This design helps
reduce genital distortion caused by this smashing.
Specialty
cylinders are proprietary and highly
customized cylinders that are considered THE FERRARI'S
of penis & scrotum cylinders. Take a look
at the Monster-Tube
Jr and the BullMaster.
These two tubes are THE ABSOLUTE BEST tubes you
can purchase because they perform the following
functions better than any other cylinder out there:
1) They eliminate the risk of pumping
until you're stuck.
2) They minimize genital distortion.
Doesn't
sound like much, but these are real issues real
pumpers run into when pumping huge!
Here
are the differences between the two cylinders,
On
getting stuck.
The Monster-Tube product line is
hinged so that after pumping your package to mammoth
dimensions, one can simply unscrew the bolts and
swing the tube open.
The
Bull Master product line already has a
4" opening but uses a flexible seal to go
between the cylinder and the groin. When it is
time to pull out, one detaches the seal from the
cylinder and pulls the package out of the 4"
opening. The gasket easily stretches around the
package thereafter.
On
genital distortion.
The Monster-Tube
Jr is small at the base (2.75"),
but HUGE and bulbous at the end (5"), so
the penis and scrotum have plenty of space to
go around. Monster-Tube.com even makes a larger
full-sized version which is much bigger.
The Bull-Master
is already 4-inches in diameter, but have added
pockets around the cylinder to house the penis
and scrotum that measure a good 5 to 5.5 inches
in diameter. These pockets form the penis into
the BullMaster mold so you come out looking like
a champ! PumpToys make a larger version called
the Bull-Master Magnum which is much bigger.
Well
that's all for the equipment portion of this article.
Now we're off to some ball pumpin routines. I
hope this article has been helpful in your quest
to find the right tube for your size, expectations
and budget. See you in the next article, Ball
Pumping Guide.
Previous
| Next Article: Ball
Pumping - pumping guide
|
Home
> Enlargement
101 > Ball Pumping Equipment
