3772 Members
4 Forums
660 Topics
2356 Posts
Max Online: 50 @ 10/09/08 12:00 AM
|
|
|
#200 - 10/11/04 10:56 PM
need serious advice
[Re: ]
|
newlou
New Forum Member
Registered: 08/24/04
Posts: 2
Loc: pennsylvania
|
Offline
|
|
should my shaft touch the interior of the cylinder? when i try to remove my penis, it gets stuck. should i get the next size? also, when i use the 2nd expansion cylinder, i experience ALOT of pain in my testicles and can only keep them in for a short amount of time. obviously, i should get the next size, or this normal?
|
|
Top
|
|
|
|
|
#201 - 10/13/04 01:11 AM
Re: need serious advice
[Re: ]
|
kaluapig
Nick
Super Pumper
Registered: 01/05/04
Posts: 336
Loc: US
|
|
Offline
|
|
Let me know what the circumference of your erect penis is (or diamter) in inches and also let me know what cylinders you bought.
Now with the 2nd expansion cylinder, start your exercise routine off at a very low pressure. As you have experienced, the testicles are not built for this kind of torture. You have to get them used to the pressures involved when pumping --- think baby steps. Once they get used to the pressure inflicted up on them, you will be able to pump to optimal levels to stretch your suspensory ligament.
Again, let me know what your dimensions are and the cylinders you purchased.
Thanks,
Nick
|
|
Top
|
|
|
|
|
#202 - 10/13/04 10:23 PM
need serious advice
[Re: ]
|
newlou
New Forum Member
Registered: 08/24/04
Posts: 2
Loc: pennsylvania
|
|
Offline
|
|
first, thanks for replying so quickly. now, to answer your questions. the circumference of my erect penis is 6". my 1st cylinder is the 2"x9". my 2nd cylinder is the 3"x9". also, when i use the 2nd cylinder, i really try to pump very slowly, but i don't always get a good seal which is why i overpump. once i do achieve a seal, i release some of the pressure (between 0.1 to 0.2) but i still ache. again, i would appreciate all of the advice you can give and thanks for your time.
|
|
Top
|
|
|
|
|
#203 - 10/18/04 12:44 AM
Re: need serious advice
[Re: ]
|
kaluapig
Nick
Super Pumper
Registered: 01/05/04
Posts: 336
Loc: US
|
|
Offline
|
|
Sir,
As you expected, the 2" cylinder is too small for you (your shaft should not be touching the insides of the walls (wall to wall).
Judging from a 6" circumference, your diameter appears to be a hair shy of 2" and the best fit for your is the 2.25" cylinder. This will give you approximately .25" for girth expansion (BTW, .25" is the perfect clearance for pumping).
As far as the penis/scrotum pumping is concerned, to correct the overpumping problem, try using a thicker lubricant such as hand lotion. If this doesn't work, try the ultimate sealant, Vaseline.
Note that Vaseline is pretty hard to clean off of your cylinder after every session so it is recomended to go with hand lotion first. The hand lotion a a bit thicker than the ID lube that came with the pump system and might work for you.
Let me know if this helps.
Nick
JN OUTLET
service@JNOUTLET.com
|
|
Top
|
|
|
|
|
|
|
by Deceiver
|
by opa
|
by 13cm_erect
|
by BigC
|
by 13cm_erect
|
|
|
